All articles
Technical Guide October 2026

Aluminium Shot Blasting Without Damage: What to Specify

Aluminium is not steel with a lighter colour. It is softer than the abrasive you are throwing at it, and the damage usually appears after painting — as a dent, a rounded edge or a visible wheel mark. Here is what to put in the specification so the machine cleans the part instead of ruining it.

How aluminium shot blasting goes wrong: five ways

Every one of them is a setting or a machine-design decision, not bad luck. When a customer sends us rejected parts, the conversation almost always lands on one of these.

01
Wheel speed set for steel
A wheel running at full speed throws shot hard enough to round off aluminium edges and mark thin walls. On a painted product those marks become rejected parts.
02
Shot that is too coarse
Large shot leaves a deep profile. Aluminium needs a shallower anchor pattern — a coarse mix from a steel job will dent the surface rather than clean it.
03
Parts hitting each other
Tumble machines clean by turning parts over on each other. Light aluminium frames bend and bruise. Hanging them on hooks removes the contact, not the blasting problem.
04
Uneven coverage on one pass
A tall frame passes four wheels at different distances. Without independent wheel control the top gets over-blasted while the bottom stays under-blasted.
05
No way to slow down
If the only setting is on or off, the operator cannot tune the machine to a thin part and has to accept damage or run too slow.

Aluminium shot blasting: the four settings that decide the finish

Four decisions cover most of the risk. None of them adds much cost at the quotation stage; all of them are expensive to fix after the machine is on your floor.

A VFD on every blast turbine
Independent wheel speed is the single most useful control on an aluminium job. Thin frames run slower, heavier sections run faster, and the setting can follow the product mix.
Hooks, not a tumble belt, for thin frames
Hanging the part removes part-on-part contact. A tumble machine is still right for small, robust castings — it is the wrong tool for a painted frame.
Shot size matched to the finish
Specify the abrasive together with the target standard. The same shot that cleans a casting will mark a 2 mm aluminium wall.
Cycle time agreed with the surface standard
If the standard is SA 3.0, that is what gets measured at acceptance — not "looks clean". Ask for the check to be written into the contract.

Micro-shot blasting on aluminium

A second group of buyers arrives with a different job: not stripping a casting, but preparing a surface for anodising, adhesive bonding or a thin powder coat. That is where micro-shot — fine cut-wire abrasive — comes in, and it behaves nothing like the coarse media used on steel.

Fine media covers more of the surface per unit of energy and leaves a shallower, more even profile. The trade is speed: micro-shot removes material slowly, so it suits a defined surface profile rather than heavy cleaning. Three things have to move together, or the result is a part that looks blasted and bonds badly:

  • Media size and shape — fine cut wire, not cast steel grit; the profile it leaves is what the next process grips.
  • Wheel speed, not just wheel power — on thin sheet the surface is made by velocity and exposure time, which is why the VFD matters more here than on a casting.
  • Separation and dust — fines and broken media have to leave the circuit; a separator that carries them back re-blasts powder and burnishes instead of profiling.

Ask for the profile, not the mesh number. Two suppliers can quote “micro-shot” and deliver very different surfaces; the measurable thing is the profile the part needs before anodising or bonding, and whether the machine can hold it across the batch.

What it looks like on a real machine

In September 2026 we shipped a Q3740 hook type machine to PT Quality Works in Surabaya, Indonesia. The parts are aluminium furniture frames, blasted to SA 3.0 before painting. The specification that made it work:

Blast turbines4 × 11 kW, each with its own VFD
HooksDual hook, 1,000 kg per hook
Chamber2,000 × 2,000 × 4,000 mm
Surface after blastingSA 3.0
ElectricalSchneider components, Siemens VFDs
Supply380 V, 3 phase, 50 Hz

The wheels ran well below maximum speed and the frames still came out at SA 3.0. The full project — photographs, videos and the electrical build — is in the Indonesia case study.

A note on dustAluminium produces fine, light dust that behaves differently from steel scale. Specify the dust collector and the filtration together with the machine, and agree who checks it — a collector sized for a steel job will clog on an aluminium one.

Questions buyers ask us

Can a tumble belt machine blast aluminium?
Yes, for small robust castings. It is the wrong choice for thin frames or anything that would show contact marks after painting.
Is SA 3.0 realistic on aluminium?
Yes, given the right shot, wheel speed and cycle time. It is a measurement, so put it in the acceptance criteria.
Do I need a VFD on every wheel?
Not on every machine, but on an aluminium job it is the cheapest way to protect thin parts while keeping throughput on heavier ones.
What is the difference between micro-shot and normal blasting on aluminium?
Micro-shot uses fine cut-wire abrasive to create a controlled surface profile for anodising, bonding or thin coatings. It removes material slowly, so it is a surface-preparation process rather than a cleaning process.
Can one machine do both cleaning and micro-shot work?
Usually not well. The media circuit, the separator and the wheel settings are built around one media size. If you need both, say so at the quotation stage instead of switching media later.
What do you need from me to quote?
The parts themselves: material, wall thickness, largest and smallest piece, batch weight, and the surface standard you have to hit.

Related: which machine type fits your part, what SA 2.5 and SA 3.0 actually measure, the hook type range, a Q3740 running aluminium at SA 3.0.

Send us the part, not just the machine type

Material, wall thickness, batch weight and the surface standard — we will tell you which machine and which settings actually suit it.